Orthopedic External Fixators

Jindal Medi Surge's [JMS] Orthopedic external fixators are medical devices used in orthopedic surgery to stabilize and immobilize fractured or damaged bones. They are typically used when traditional casting or splinting is not sufficient for proper bone alignment and healing. External fixators are designed to provide stability, alignment, and support for the bone while allowing for better access to the injury site and the surrounding soft tissues. Here are some key features and components of orthopedic external fixators: Rings or Clamps: These are attached to the bone on either side of the fracture with pins or wires. The rings or clamps serve as anchor points for the fixator. Connecting Rods or Struts: These are used to connect the rings or clamps and maintain the desired distance and alignment between them. Adjustability: External fixators are highly adjustable, allowing orthopedic surgeons to make precise adjustments to ensure proper bone alignment and to accommodate changes in the healing process. Biocompatibility: Materials used in external fixators are typically biocompatible to minimize the risk of allergic reactions or tissue rejection. Radiolucency: Some external fixators are designed to be radiolucent, meaning they do not block X-rays, allowing healthcare professionals to monitor the healing process without interference. Durability: External fixators need to be durable and able to withstand the stresses and forces placed on them during the healing process. Anchoring Devices: These are pins or wires that are inserted into the bone, providing a secure attachment point for the rings or clamps. Orthopedic external fixators are commonly used in the following situations: Complex Fractures: For fractures that are difficult to stabilize using traditional methods, such as open or comminuted fractures. Limb Length Discrepancies: To correct or manage differences in limb length caused by fractures, growth plate injuries, or other orthopedic conditions. Limb Deformities: To correct angular or rotational deformities in the bones of the limbs. Bone Infections: In cases where there is a bone infection, external fixators can provide better access for wound care and antibiotic therapy. Non-Unions and Malunions: To address cases where bones have not healed properly (non-union) or have healed in an improper position (malunion). It's important to note that the specific design and configuration of orthopedic external fixators can vary based on the patient's condition and the surgeon's preferences. The choice of external fixator and its placement is a decision made by the orthopedic surgeon, and the device is typically customized to the individual patient's needs. The fixator is often removed once the bone has healed sufficiently.

CATALOUGE

Orthopedic External Fixator Catalog-JMS.pdf

PRODUCT LIST

Orthopedic External Fixator Prices-JMS.pdf

PRODUCT RANGE

Tubular External Fixators


External Fixator Clamps

4210.001000 Single Pin Adjustable Clamp With Open Vice

4210.001.1 Single Pin Adjustable Clamp With Open Vice (6.0mm Pin)

4210.002100 Single Pin Adjustable Clamp With Fixed Vice 11.0mm (7mm Threaded Part)

4210.002200 Single Pin Adjustable Clamp With Fixed Vice 11.0mm (7mm Threaded Part) (6.0mm Pin)

4210.002300 Single Pin Adjustable Clamp With Fixed Vice 11.0mm (7mm Threaded Part) (6.5mm Pin)

4210.0021T Single Pin Adjustable Clamp With Fixed Vice 11.0mm (7mm Threaded Part) Titanium

4210.002110 Single Pin Adjustable Clamp With Fixed Vice 8.0mm (7mm Threaded Part)

4210.0011IND Single Pin Clamp (Indian Design)

4210.001DIND Double Pin Clamp (Indian Design)

4210.010IND Tube To Tube Clamp (Indian Design)

4210.009IND Transverse Clamp (Indian Desgin)

4210.009OIND Open Single Pin Clamp (Indian Desgin)

4210.003000 Double Pin Clamp

4210.003100 Double Pin Clamp 8mm

4210.004000 Open Single Pin Clamp

4210.005000 Connecting Clamp

4210.006000 Open Connecting Clamp Ao Type

4210.007000 Twin Adjustable Clamp Straight / Curved (7mm Thread Special Quality)

4210.007100 Twin Adjustable Clamp Straight / Curved

4210.009000 Transverse Clamp

4210.010000 Tube To Tube Clamp 11mm

4210.010T Tube To Tube Clamp 11mm Titanium

4210.010100 Tube To Tube Clamp 8mm Rod

4210.0101T Tube To Tube Clamp 8mm Rod Titanium

4210.011000 Clip On Self Holding Clamp - SS

4210.011LT Combination Clamp Clip on Self Holding Large 11mm x 5mm Titanium

4210.011LA Combination Clamp Clip on Self Holding Large 11mm x x5mm Aluminium

4210.011LS Combination Clamp Clip on Self Holding Large 11mm x 5mm S.S.

4210.011LT Combination Clamp Clip on Self Holding Medium 8mm x 4mm Titanium

4210.011LA Combination Clamp Clip on Self Holding Medium 8mm x 4mm Aluminium

4210.011LS Combination Clamp Clip on Self Holding Medium 8mm x 4mm S.S.

4210.011S Clip On Self Holding Clamp Small (S.S. + Aluminium) Tur Desgin

4210.011T Clip On Self Holding Clamp (Titanium)

4210.012T Clip On Self Holding Clamp 8mm (Titanium)

4210.030000 Compression Distraction Device Large

4210.030100 Compression Distraction Device Small

4210.030300 Small Open Clamp

4210.030400 Medium Clamp

4210.030500 Adjustable Half Pin Clamp

4210.030600 Adjustable Wire Pin Clamp A.O. Type

4210.031100 Femoral Joint (Mono Axial)

4210.031200 Femoral Joint (Poly Axial)

4210.031300 Translation / Rotation Device

4210.031400 Orthofix (Aluminium) Collex Fixator

4210.031500 Aluminium Clamp Large 7.90mm x 4.75mm

4210.031600 Aluminium Clamp Medium 6.30mm x 3.10mm

4210.031700 Aluminium Clamp Small 5.0mm x 3.10mm

4210.031800 Fiber Fixator Large

4210.031900 Fiber Fixator Small

4210.032000 Clamps For 6mm Rod

4210.032100 Hybrid Right Angle Clamp

4210.032200 Hybrid Straight Clamp

4210.032300 Titanium Alloy Clamp Set ( Mal Design)

4210.032310 Spanner 7mm

4210.032320 Spanner 10mm

4210.032330 Spanner 13mm

4210.032340 Screw Driver 7mm

4210.032350 Aluminium Graphic Box For Titanium Clamp

4210.033000 Washer (Mal Desgin) (316L)

4210.033100 Allen Key (Two Sided) (Special Mal Design)

4213.001600 Mini TWrench For Mini Clamps (Special Mex Design)


External Fixator Forearm & Metacarpals

4213.001000 Mini Clamp 4 X 2.5mm (Indian Design)

4213.001300 Mini Clamp 4 X 4mm (Indian Design)

4213.001100 Small Clamp For Metacarpals 4.0mm X 2.5mm (Nut Hex Size: 7mm)

4213.001200 Small Open Clamp For Metacarpals 4.0mm X 2.5mm (Nut Hex Size: 7mm)

4213.001400 Small Clamp For Forearm 4.0mm X 4.0mm (Nut Hex Size: 7mm)

4213.001500 Small Open Clamp For Forearm 4.0mm X 4.0mm (Nut Hex Size: 7mm)

4210.030200 Small Close Clamp 2.5mm x 5.0mm Sm Ext. Fix

4210.030210 Small Open Clamp 2.5mm x 5.0mm Sm Ext. Fix

4210.030300 Small Open Connecting Clamp 4mm x 4mm (clip-design)


Line-x-fix Set

LF.001 Line-x-fix Clamp

4LFIX.002 Schanz Pin 5 x 200mm

4LFIX.003 Rod 8 x 200mm


Colles Fixator 

4205.525100 Colles Fixator 145mm

Schanz Screw 3.0 x 100mm / 24mm Thread

Schanz Screw 2.5 x 80mm / 20mm Thread

Wrench 

Allen Key 


4205.525200 Colles Fixator 165mm

Schanz Screw 3.0 x 100mm / 24mm Thread

Schanz Screw 2.5 x 80mm / 20mm Thread

Wrench 

Allen Key 


Aesculap Clamp

4210.03073IND Aesculap Clamp (Indian Design)

4210.030900 Aesculap Clamp Mini (Tube + Pin)

4210.030910 Aesculap Clamp Mini (Tube + Tube)

4210.030920 Aesculap Clamp Mini

4210.031000 Aesculap Clamp Large

4210.031100 Aesculap Clamp Large (Aluminium)

4210.041000 Aesculap Universal Clamp Large (Mal Desgin) (Matt Finish) (Tube + Pin)

4210.041010 Aesculap Universal Clamp Large (Mal Desgin) (Matt Finish) (Tube + Tube)

TE8-TH-JM Tube Element For 8mm Tubes Threaded

TE8-UTH-JM Tube Element For 8mm Tubes UnThreaded

UCTE8-TH-JM Tube Element For 8mm Tubes Threaded (Upper Cut)

UCTE8-UTH-JM Tube Element For 8mm Tubes UnThreaded (Upper Cut)

PE45-TH-JM Pin Element For 8mm Tubes Threaded (4 & 5mm)

PE45-UTH-JM Pin Element For 8mm Tubes UnThreaded (4 & 5mm)

PE56-UTH-JM Pin Element For 8mm Tubes UnThreaded (5 & 6mm)


Spacer Disc

SD-05-JM 0.5mm

SD-20-JM 2.0mm

SD-40-JM 4.0mm

SD-80-JM 8.0mm

SD-100-JM 10.0mm


Bolt

HB-25-JM 25mm

HB-20-JM 20mm

HB-30-JM 30mm


Double Clamp to Rod

112.001000 12 x 5

112.002000 18 x 8

112.003000 18 x 18

112.004000 12 x 12

112.005000 18 x 12


Tube To Tube Clamp - Aluminium

113A.001 18 x 18

113A.002 18 x 12

113A.003 12 x 12

113A.004 12 x 8

113A.004 12 x 5


Tube to Tube Clamp - SS

113S.001 18 x 18

113S.002 18 x 12

113S.003 12 x 12

113S.004 12 x 8

113S.004 12 x 5


Connecting 3.10mm Rods - SS

4139.115100 100mm

4139.115200 150mm


Connecting 4mm Rods For Forearm & Metacarples - SS

4140.115000 60mm

4140.115100 100mm

4140.115200 150mm

4140.115300 200mm

4140.115400 250mm

4140.115500 300mm

4140.115600 350mm


Connecting 4.75mm Rods - SS

4141.115100 100mm

4141.115200 150mm

4141.115300 200mm


5mm Connecting Rods - SS

4140.115510 100mm

4140.115520 150mm

4140.115530 200mm

4140.115540 250mm

4140.115550 300mm

4140.115560 350mm


6mm Connecting Rods - SS

4140.115551 100mm

4140.115552 150mm

4140.115553 200mm

4140.115554 250mm

4140.115555 300mm


Tubular Rods 8mm (1mm Wall Thickness) - SS

4210.059800 100mm (4'')

4210.059900 125mm (5'')

4210.060000 150mm (6'')

4210.060100 200mm (8'')

4210.060200 250mm (10'')

4210.060300 300mm (12'')

4210.060400 350mm (14"')

4210.060500 400mm (16'')

4210.060600 450mm (18'')

4210.060700 500mm (20'')


Connecting Rods 8mm - SS

4210.070000 100mm

4210.071000 125mm

4210.072000 150mm

4210.073000 200mm

4210.074000 250mm

4210.075000 300mm

4210.076000 350mm

4210.077000 400mm

4210.078000 450mm

4210.079000 500mm


Connecting Rods 8mm - AL

4210A.07 100mm

4210A.071 125mm

4210A.072 150mm

4210A.073 200mm

4210A.074 250mm

4210A.075 300mm

4210A.076 350mm

4210A.077 400mm

4210A.078 450mm

4210A.079 500mm


Tubular Rods 11mm - SS

4210.050000 100mm (4'')

4210.050100 125mm (5'')

4210.051000 150mm (6'')

4210.052000 200mm (8'')

4210.053000 250mm (10'')

4210.054000 300mm (12'')

4210.055000 350mm (14"')

4210.056000 400mm (16'')

4210.057000 450mm (18'')

4210.058000 500mm (20'')


Connecting Rod 4.70mm - Aluminium

4210.470100 100mm

4210.470200 130mm

4210.470300 150mm

4210.470400 200mm

4210.470500 250mm


Connecting Rod 6.30mm - Aluminium

4210.630100 100mm

4210.630200 150mm

4210.630300 200mm

4210.630400 250mm


Connecting Rod 7.90mm - Aluminium

4210.790100 100mm

4210.790200 150mm

4210.790300 200mm

4210.790400 250mm

4210.790500 300mm

4210.790600 350mm

4210.790700 400mm

4210.790800 450mm


JMS.035S Tubular External Fixator Set - Small

4213.001100 Small Clamp For Metacarpals 4.0mm X 2.5mm (Nut Hex Size: 7mm)

4213.001200 Small Open Clamp For Metacarpals 4.0mm X 2.5mm (Nut Hex Size: 7mm)

4213.001400 Small Clamp For Forearm 4.0mm X 4.0mm (Nut Hex Size: 7mm)

4213.001500 Small Open Clamp For Forearm 4.0mm X 4.0mm (Nut Hex Size: 7mm)

4210.030300 Small Open Connecting Clamp 4mm x 4mm (clip-design)

Connecting 4mm Rods For Forearm & Metacarples - SS

4140.115000 60mm

4140.115100 100mm

4140.115200 150mm

4140.115300 200mm

4140.115400 250mm

4140.115500 300mm

4140.115600 350mm

Front Threaded Pin (Schanz Screw)

4211.301410 Dia 2.5mm Length 100mm

4211.301500 Dia 2.5mm Length 150mm

4211.301600 Dia 2.5mm Length 175mm

4211.001000 Dia 4.0mm Length 125mm Thread 18mm

4211.401000 Dia 4.0mm Length 150mm

4211.002100 Dia 4.0mm Length 175mm Thread 50mm

JHF.023 7mm Spanner Wrench

Drill Bit S.S. Quick Coupling End (S.S.420)

4260.205110 2.0 X 160mm

4260.375000 Dia 3.5mm X 200mm Long

4400.015000 Instrument Box With Two Tray Length 450mm


JMS.035 Tubular External Fixator Set - Large

4210.002100 Single Pin Adjustable Clamp With Fixed Vice 11.0mm (7mm Threaded Part)

4210.004000 Open Single Pin Clamp

4210.005000 Connecting Clamp

4210.007000 Twin Adjustable Clamp Straight / Curved (7mm Thread Special Quality)

4210.009000 Transverse Clamp

4210.010000 Tube To Tube Clamp

4210.030000 Compression Distraction Device Large

4210.032000 Connecting Rod 5.0mm

4210.034100 Sleeve For 5.0mm Shanz Pin With Handle

4210.034200 Sleeve For 4.8mm Shanz Pin With Handle

4210.036000 Triple Trocar Set With Handle

JHF.024 11mm Spanner Wrench

Tubular Rods 11mm - SS

4210.050000 100mm (4'')

4210.051000 150mm (6'')

4210.052000 200mm (8'')

4210.053000 250mm (10'')

4210.054000 300mm (12'')

4210.055000 350mm (14"')

4210.056000 400mm (16'')

4211.005000 Front Threaded Pin (Shanz Screw) Dia 4.5mm Length 150mm Thread 18mm

4211.011000 Front Threaded Pin (Shanz Screw) Dia 4.5mm Length 200mm Thread 25mm

4211.014000 Front Threaded Pin (Shanz Screw) Dia 4.5mm Length 225mm Thread 25mm

4211.025000 Front Threaded Pin (Shanz Screw) Dia 5.0mm Length 150mm Thread 18mm

4211.031000 Front Threaded Pin (Shanz Screw) Dia 5.0mm Length 200mm Thread 25mm

4211.034000 Front Threaded Pin (Shanz Screw) Dia 5.0mm Length 225mm Thread 25mm

4260.375000 Drill Bit S.S. Q.C. End Dia 3.5mm X 200mm Long

4260.475000 Drill Bit S.S. Q.C. End Dia 4.5mm X 200mm Long

4400.015000 Instrument Box With Two Tray Length 450mm


8100S.03 External Fixator Set (AO TYPE BOX DETAILS)

Single Pin Clamp 11mm

Single Pin Clamp 8mm

Tube to Tube Clamp 11mm

Tube to Tube Clamp 8mm

Transverse Clamp

Schanz Pin 4 x 90mm

Schanz Pin 5 x 110mm

Schanz Pin 5 x 130mm

Schanz Pin 6 x 130mm

Schanz Pin Cancellous 5 x 150mm

Schanz Pin Cancellous 6 x 150mm

Drill Bit 2.8 x 200mm

Drill Bit 3.8 x 200mm

Drill Bit 4.8 x 200mm

Screw Driver 4mm

Screw Driver 5mm

Drill Sleeve 4mm

Drill Sleeve 5mm

Drill Sleeve 6mm

Open Wrench 10mm

Carbon Fiber Rod 8 x 150mm

Carbon Fiber Rod 8 x 200mm

Carbon Fiber Rod 8 x 250mm

Carbon Fiber Rod 8 x 300mm

Carbon Fiber Rod 11 x 150mm

Carbon Fiber Rod 11 x 200mm

Carbon Fiber Rod 11 x 250mm

Carbon Fiber Rod 11 x 300mm

Carbon Fiber Rod 11 x 350mm

Graphic Box


8100J.03 External Fixator Set (JMS TYPE BOX DETAILS)

Single Pin Clamp 11mm

Tube to Tube Clamp 11mm

Double Pin Clamp

Tube to Tube Clamp 8mm

Transverse Clamp

Schanz Pin 5 x 150mm

Schanz Pin 5 x 175mm

Schanz Pin 5 x 200mm

Schanz Pin 6 x 225mm

Drill Bit 2.8 x 200mm

Drill Bit 3.8 x 200mm

Drill Bit 4.8 x 200mm

Screw Driver 4mm

Screw Driver 5mm

Drill Sleeve 4mm

Drill Sleeve 5mm

Drill Sleeve 6mm

Open Wrench 10mm

Carbon Fiber Rod 8 x 150mm

Carbon Fiber Rod 8 x 200mm

Carbon Fiber Rod 8 x 250mm

Carbon Fiber Rod 8 x 300mm

Carbon Fiber Rod 11 x 150mm

Carbon Fiber Rod 11 x 200mm

Carbon Fiber Rod 11 x 250mm

Carbon Fiber Rod 11 x 300mm

Carbon Fiber Rod 11 x 350mm

Carbon Fiber Rod 11 x 400mm

Graphic Box

s (Rapid Tightening Of Nuts)


Ilizarov External Fixators


Half Ring S.S.

4230.008000 80mm

4230.010000 100mm

4230.012000 120mm

4230.014000 140mm

4230.014100 150mm

4230.016000 160mm

4230.018000 180mm

4230.020000 200mm

4230.022000 220mm

4230.024000 240mm


Half Ring Titanium

4230T.014 140mm

4230T.016 160mm

4230T.018 180mm

4230T.020 200mm

4230T.022 220mm

4230T.024 240mm


5/8Th Ring - SS

4231.010000 100mm

4231.012000 120mm

4231.014000 140mm

4231.014100 150mm

4231.016000 160mm

4231.018000 180mm

4231.020000 200mm

4231.022000 220mm

4231.023000 240mm


5/8Th Ring - Titanium

4231T.010 100mm

4231T.012 120mm

4231T.014 140mm

4231T.0141 150mm

4231T.016 160mm

4231T.018 180mm

4231T.020 200mm

4231T.022 220mm

4231T.023 240mm


5/8Th Ring Aluminium

4231AL.010 115mm

4231AL.012 140mm

4231AL.014 165mm

4231AL.0141 205mm


Full Ring

4231.022.1 80mm Id 120mm Od

4231.022.2 100mm Id 140mm Od

4231.022.3 110mm Id 150mm Od

4231.022.4 120mm Id 160mm Od

4231.022.5 130mm Id 170mm Od

4231.022.6 140mm Id 180mm Od

4231.022.7 150mm Id 190mm Od

4231.022.8 160mm Id 200mm Od

4231.022.9 180mm Id 220mm Od

4231.022.10 200mm Id 240mm Od


Omega Ring

5OR.120 120mm

5OR.140 140mm

5OR.160 160mm

5OR.180 180mm

5OR.200 200mm


Italian Femoral Arch 90°

4232.010000 100mm

4232.012000 120mm

4232.014000 140mm

4232.016000 160mm

4232.018000 180mm

4232.020000 200mm

4232.022000 220mm


Italian Femoral Arch 120°

4233.010000 100mm

4233.012000 120mm

4233.014000 140mm

4233.016000 160mm

4233.018000 180mm

4233.020000 200mm

4233.022000 220mm

4233.024000 240mm


Single Pin Fixation Bolt

4235.000000 Single Pin Fixation Bolt 3.5mm

4235.000100 Single Pin Fixation Bolt 4.5mm

4235.000200 Single Pin Fixation Bolt 2.0mm

4235.000300 Single Pin Fixation Bolt 5.0mm

4235.000400 Single Pin Fixation Bolt 6.0mm


Oblique Support

4236.000000 Oblique Support With Thread

4236.001000 Oblique Support With NonThread


Threaded Rod

4237.000100 40mm Length

4237.000200 60mm Length

4237.000300 75mm Length

4237.000400 80mm Length

4237.000500 100mm Length

4237.000600 120mm Length

4237.000700 125mm Length

4237.000800 140mm Length

4237.000900 150mm Length

4237.001000 160mm Length

4237.001100 180mm Length

4237.001200 200mm Length

4237.001300 250mm Length

4237.001400 300mm Length

4237.001500 350mm Length

4237.001600 400mm Length

4237.001700 450mm Length


Threaded Rod (With Hole)

4237.000000 40mm Length

4237.001000 60mm Length

4237.002000 75mm Length

4237.003000 80mm Length

4237.004000 100mm Length

4237.005000 120mm Length

4237.006000 125mm Length

4237.008000 150mm Length

4237.009000 180mm Length

4237.010000 200mm Length

4237.012000 250mm Length

4237.014000 300mm Length

4237.016000 350mm Length

4237.018000 400mm Length

4237.020000 450mm Length


Threaded Rod Slotted

4238.000000 40mm Length

4238.001000 60mm Length

4238.002000 75mm Length

4238.003000 80mm Length

4238.004000 100mm Length

4238.005000 120mm Length

4238.006000 125mm Length

4238.008000 150mm Length

4238.009000 180mm Length

4238.010000 200mm Length

4238.011000 250mm Length

4238.012000 300mm Length

4238.013000 350mm Length

4238.014000 400mm Length


Threaded Rods Partial Threaded

4238.014.01 130mm

4238.014.02 170mm

4238.014.03 210mm


Telescopic Rod

4239.009000 75mm Length

4239.010000 100mm Length

4239.015000 150mm Length

4239.020000 200mm Length

4239.025000 250mm Length

4239.030000 300mm Length


Graduated Telescopic Rod

4240.010000 100mm Length

4240.015000 150mm Length


Post Female

4241.001000 1 Holes

4241.002000 2 Holes

4241.003000 3 Holes

4241.004000 4 Holes

4241.005000 5 Holes


Post Male

4242.001000 1 Holes

4242.002000 2 Holes

4242.003000 3 Holes

4242.004000 4 Holes

4242.005000 5 Holes


Hinge

4243.010000 Hinge Female

4243.020000 Hinge Male

4243.030000 Hinge 90°


Hinge (Low Profile)

4243.010110 Hinge Female

4243.020110 Hinge Male

4243.030110 Hinge 90°


Wrenchoqube

4243.030100 1 Holes

4243.030200 2 Holes

4243.030300 3 Holes

4243.030400 4 Holes

4243.030500 5 Holes


4243.030510 Set Screw For Wrenchoqube (8mm Long)


Blocks For Half Pins To Be Used With Sleeves

4243.03.01 1 Holes

4243.03.02 2 Holes

4243.03.03 3 Holes

4243.03.04 4 Holes

4243.03.05 5 Holes


Sleeves For Wrenchoqube

4243.3.011 3mm

4243.3.012 4mm

4243.3.013 5mm

4243.3.014 6mm


Short Connection Plate

4244.002000 2 Holes

4244.003000 3 Holes

4244.004000 4 Holes

4244.005000 5 Holes

4244.006000 6 Holes

4244.007000 7 Holes

4244.008000 8 Holes

4244.009000 9 Holes

4244.010000 10 Holes

4244.011000 11 Holes

4244.012000 12 Holes


Long Connecting Plate

4244.012100 6 Holes

4244.012200 7 Holes

4244.012300 8 Holes

4244.012400 9 Holes

4244.012500 10 Holes

4244.012600 11 Holes

4244.012700 12 Holes

4244.012710 17 Holes


Long Connection Plate With Threaded End

4245.005000 5 Holes

4245.006000 6 Holes

4245.007000 7 Holes

4245.008000 8 Holes

4245.009000 9 Holes

4245.010000 10 Holes

4245.011000 11 Holes

4245.012000 12 Holes

4245.013000 13 Holes

4245.014000 14 Holes

4245.015000 15 Holes


Foot Rings S.S.

4245.015100 140mm Short

4245.015200 140mm Long

4245.015300 160mm Short

4245.015400 160mm Long

4245.015500 180mm Short

4245.015600 180mm Long


Twisted Plate

4246.001000 1 Holes

4246.002000 2 Holes

4246.003000 3 Holes

4246.004000 4 Holes

4246.005000 5 Holes


Bushing

4246.211100 20mm

4246.211200 30mm

4246.211300 40mm

4246.211400 50mm

4246.211500 60mm


Threaded Socket

4247.002000 20mm

4247.003000 30mm

4247.004000 40mm

4247.005000 50mm

4247.006000 60mm

Ilizarov Wire

4248.010000 Ilizarov Wire 1.5mm Bayonet Point Length 400mm

4248.010100 Ilizarov Wire 1.5mm Bayonet Point Length 370mm

4248.012000 Ilizarov Wire 1.8mm Bayonet Point Length 400mm

4248.012100 Ilizarov Wire 1.8mm Bayonet Point Length 370mm

4248.014000 Ilizarov Wire 1.5mm Trocar Point Length 400mm

4248.014100 Ilizarov Wire 1.5mm Trocar Point Length 370mm

4248.016000 Ilizarov Wire 1.8mm Trocar Point Length 400mm

4248.016100 Ilizarov Wire 1.8mm Trocar Point Length 370mm


Olive Wire

4248.018000 Olive Wire 1.5mm Trocar Point Length 400mm

4248.026100 Olive Wire 1.8mm Trocar Point Length 400mm

4248.019000 Olive Wire 1.5mm Bayonet Point Length 400mm

4248.021000 Olive Wire 1.8mm Bayonet Point Length 400mm


Olive Wire Bayonet Point (Made From One Piece)

4248.021100 Olive Wire 1.5mm Bayonet Point Length 400mm

4248.021200 Olive Wire 1.8mm Bayonet Point Length 400mm

4248.021300 Olive Wire 1.5mm Trocar Point Length 400mm

4248.021400 Olive Wire 1.8mm Trocar Point Length 400mm


Circlage Wire With Loop 280mm Long

4193.217000 17 Swg (1.5mm)

4193.218000 18 Swg (1.25mm)

4193.219000 19 Swg (1.0mm)

4193.220000 20 Swg (0.9mm)

4193.221000 21 Swg (0.8mm)


Circlage Wire With Loop 300mm Long

4193.221100 0.4mm

4193.221200 0.5mm

4193.221300 0.6mm

4193.221400 0.7mm

4193.221500 0.8mm

4193.221600 0.9mm

4193.221700 1.0mm

4193.221800 1.2mm

4193.221900 1.5mm

4193.222000 1.6mm


Circlage Wire With Loop 600mm Long

4193.317000 17 Swg (1.5mm)

4193.318000 18 Swg (1.25mm)

4193.319000 19 Swg (1.0mm)

4193.320000 20 Swg (0.9mm)

4193.321000 21 Swg (0.8mm)

Nuts Bolts Washers

4249.101000 Wire Fixation Bolt Cannulated

4249.102000 Wire Fixation Bolt Slotted

4249.103000 Cannulated Bolt With Female Thread In Head

4249.103100 Slotted Bolt With Female Thread In Head

4249.104000 Wire Buckle

4249.105100 Space Washer

4249.105200 Washer

4249.105300 Thick Washer 2mm

4249.105310 Thick Washer 3mm

4249.105400 Thick Washer 4mm

4249.105500 Side Sloted Washer 3mm

4249.105600 Side Sloted Washer 4mm

4249.105700 Center Sloted Washer

4249.105800 Side Flated Washer

4249.105900 Split Washer

4249.106000 Couple Washer

4249.106010 Star Washers

4249.106100 Lengthning Tower

4249.106110 Ring Connection Bolt 10mm

4249.106120 Ring Connection Bolt 15mm

4249.106130 Ring Connection Bolt 20mm

4249.107000 Nut 10mm

4249.108000 Square Nut

4249.109000 Nylon Insert Nut

4249.113000 Repofix Device

4249.117100 Universal Joint

4249.310100 Schanze Screw Fixation Bolt 4.0mm / 4.5mm

4249.310200 Hex Nut 6mm

4249.310300 Nut With Qardigonal Head

4249.310400 Orthofix (Aluminum)

4249.310500 Orthofix (Ball & Socket)

4249.310600 Washer 2.0mm Thick 26.5mm Od & 6.0mm Id

4246.110000 Curved Plate 3 Holes

4246.111.1 Set Screw For Ilizarov

4234.000000 Multipin Fixation Clamp

4234.000100 Connecting Bolt 6mm Thread


Instruments

4250.203100 Angulated Wrench TwoInOne

4250.203110 Angulated Wrench L Type

4252.401100 Wire Tensioner Mechanical 2

4252.402000 Wire Tensioner Dynmometere

4252.402100 U Shape Wrench For Nuts (Mal Desgin)

4252.402200 Wrench 10mm

4252.402300 Wrench 12mm

4252.402400 Wrench 13mm

4252.402500 Wrench 14mm

4252.402600 Universal TWrench Swing Box Design 10mm

4252.402610 Drill Guide 4.8mm

4252.402620 Screw Guide 6mm

4252.402630 Trocar 6mm

4252.402640 Straight Screw Driver For Set Screws AcroSS Flat 3mm

4252.402650 90Deg. Screw Driver For Set Screws 3mm

4252.402660 Box Wrench 8mm


Pediatric Ilizarov External Fixators (Made To Order)


Half Ring Pediatric

4249.310700 80mm

4249.310800 100mm

4249.310900 120mm

4249.311000 140mm


5/8 Rings Pediatric

4249.311100 80mm

4249.311200 100mm

4249.311300 120mm

4249.311400 140mm


Hinge Pediatric

4249.311500 Male

4249.311600 Female

4249.311700 Fixed 90Degree


Post Pediatric

4249.311800 2 Hole ( Male)

4249.311900 2 Hole (Female )

4249.312000 3 Hole (Male)

4249.312100 3 Hole (Female )


Threaded Socket Pediatric

4249.312200 20mm

4249.312300 30mm

4249.312400 40mm

4249.312500 60mm


Wire Fixation Bolt Pediatric

4249.313400 Slotted

4249.313500 Cannulated


Wrencho Cube Pediatric Pediatric

4249.313600 1 Hole ( Without Bolts)

4249.313700 2 Hole ( Without Bolts)

4249.313800 3 Hole ( Without Bolts)


Short Connection Plate Pediatric

4249.313900 2 Hole

4249.314000 3 Hole


Threaded Rod Pediatric

4249.314100 M5 (Per Inch)

4249.314200 Slotting Charges Extra Per Rod


Pediatric Nuts Bolts & Washers

4249.314300 Nuts M5

4249.314400 Square Nut

4249.314600 Ring Connecting Bolts

4249.314700 Spacing Washers

4249.314800 Bushings

4249.314900 Square Nut

4249.314500 T Handle


Ilizarov Sets

JIS.S Ilizarov Set Small S.S.

Ilizarov 1/2 Ring Size: 80mm SS

Ilizarov 1/2 Ring Size: 100mm SS

Ilizarov 1/2 Ring Size: 120mm SS

Wire Fixation Bolt Cannulated SS

Connection Bolt

Telescopic Rod : 100mm

Nut : 10mm SS

Threaded Rod Length 100mm

Threaded Rod Length 150mm

Threaded Rod Length 200mm

Short Connection Plate 3 Holes SS

Short Connection Plate 4 Holes SS

Post Male2 Holes SS

Post Female2 Holes SS

Spacing Washer SS

Hinge Male SS

Hinge Female SS

Threaded Socket Length : 20mm SS

Threaded Socket Length : 30mm SS

Threaded Socket Length : 40mm SS

Ilizarov Wire 1.8mm X 400mm Bayonet Point SS

Olive Wire 1.8mm X 400mm SS

Stainless Steel


JIS.M Ilizarov Set Medium S.S.

Ilizarov 1/2 Ring Size: 140mm SS

Ilizarov 1/2 Ring Size: 160mm SS

Ilizarov 5/8Th Ring Size: 140mm SS

Ilizarov 5/8Th Ring Size: 160mm SS

Wire Fixation Bolt Cannulated SS

Connection Bolt SS

Telescopic Rod Length:100mm SS

Telescopic Rod Length:150mm SS

Threaded Rod Length:100mm SS

Threaded Rod Length:150mm SS

Threaded Rod Length:200mm SS

Nut 10mm SS

Short Connection Plate 3 Holes SS

Short Connection Plate 4 Holes SS

Short Connection Plate 5 Holes SS

Short Connection Plate 6 Holes SS

Short Connection Plate 7 Holes SS

Post Male 3 Holes SS

Post Female 3 Holes SS

Spacing Washer SS

Hinge Male SS

Hinge Female SS

Threaded Socket Length : 20mm SS

Threaded Socket Length : 30mm SS

Threaded Socket Length : 40mm SS

Front Threaded Pin (Shanz Screws) Dia: 5.0mm L 200mm Thread: 32mm SS

Shanz Pins Fixation Bolt

Ilizarov Wire 1.8 X 400mm Bayonet Point SS

Olive Wires 1.8 X 400mm SS

Stainless Steel


JIS.L Ilizarov Set Large S.S.

Ilizarov 1/2 Ring Size 180mm SS

Ilizarov 1/2 Ring Size 200mm SS

Ilizarov 1/2 Ring Size 220mm SS

Ilizarov 5/8Th Ring Size: 180mm SS

Ilizarov 5/8Th Ring Size: 200mm SS

Ilizarov 5/8Th Ring Size: 220mm SS

Italian Femoral Arche 120° Size: 180mm SS

Italian Femoral Arche 120° Size: 200mm SS

Italian Femoral Arche 120° Size: 220mm SS

Wire Fixation Bolt Cannulated SS

Connection Bolt SS

Telescopic Rod Length 100mm SS

Telescopic Rod Length 150mm SS

Telescopic Rod Length 200mm SS

Graduated Telescopic Rod Length 150mm SS

Threaded Rod Length 150mm SS

Threaded Rod Length 200mm SS

Threaded Rod Length 250mm SS

Nut 10mm SS

Short Connection Plate 3 Holes SS

Short Connection Plate 4 Holes SS

Short Connection Plate 5 Holes SS

Short Connection Plate 6 Holes SS

Short Connection Plate 7 Holes SS

Post Male 4 Holes SS

Post Female 4 Holes SS

Hinge Male SS

Hinge Female SS

Spacing Washer SS

Threaded Socket Length : 20mm SS

Threaded Socket Length : 30mm SS

Threaded Socket Length : 40mm SS

Front Threaded Pins (Shanz Screws) Dia: 5.0mm L 225mm Thread: 40mm SS

Shanz Pins Fixation Bolts

Oblique Support Without Thread

Ilizarov Wire 1.8mm X 400mm Bayonet Point SS

Olive Wire 1.8mm X 400mm SS

Stainless Steel


Jess Fixator


Jess Clamps

Distractor

4252.402100 M4 Single Hole ( Adler Type All Sizes )

4252.402200 Double Hole ( Adler Type All Sizes )


Distractor 6mm Double Hole

4252.402410 6 Inch

4252.402420 8 Inch

4252.402430 10 Inch

150mm & 200mm

250mm 300mm & 350mm

4252.402600 Link Joint Small

4252.402610 Link Joint Medium

4252.402620 Link Joint Large

4252.402700 Connecting Rods Per Inch ( Knurled )

4252.402800 L Rod

4252.402900 Z Rod

4252.403000 Allen Key ( 2.5mm & 3.0mm )

4252.403100 Foot Plate


Ctev (JeSS) Fixator Sets

JCTEV-S Ctev External Fixator Set (Small)

Link Joints Small

Connecting Rod Dia : 2.5mm Length : 100mm

Connecting Rod Dia : 2.5mm Length : 150mm

Connecting Rod Dia : 2.5mm Length : 200mm

L' Rod Dia : 2.5mm

Z' Rod Dia : 2.5mm

Distractor Double Hole Length : 100mm

Distractor Double Hole Length : 150mm

K. Wire Dia : 1.5mm X 150mm

K. Wire Dia : 2.0mm X 150mm

Foot Plate

Allen Key 2.5mm


JCTEV-M Ctev External Fixator Set (Medium)

Link Joints Medium

Connecting Rod Dia : 3.0mm Length : 125mm

Connecting Rod Dia : 3.0mm Length : 150mm

Connecting Rod Dia : 3.0mm Length : 200mm

L' Rod Dia : 3.0mm

Z' Rod Dia : 3.0mm

Distractor Double Hole Length : 150mm

Distractor Double Hole Length : 200mm

K. Wire Dia : 2.0mm X 150mm

K. Wire Dia : 2.5mm X 150mm

Foot Plate

Allen Key 3.0mm


JCTEV-L Ctev External Fixator Set (Large)

Link Joints Large

Connecting Rod Dia : 4.0mm X 125mm

Connecting Rod Dia : 4.0mm X 150mm

Connecting Rod Dia : 4.0mm X 200mm

L' Rod Dia : 4.0mm

Z' Rod Dia : 4.0mm

Distractor Double Hole Length : 150mm

Distractor Double Hole Length : 250mm

K. Wire Dia : 2.5mm X 150mm

Foot Plate

Allen Key 3.0mm


The Rail & Dynamic External Fixation System


Rail External Fixators - JMS DESIGN

Adult

4205J.02 Rail Length 250mm

4205J.03 Rail Length 300mm

4205J.035 Rail Length 350mm

4205J.04 Rail Length 400mm

4205J.05 Central Clamp

4205J.055 End Clamp

4205J.065 Ball Joint Coupling Clamp

4205J.07 T Ball Joint Coupling Clamp

4205J.075 T Clamp

4205J.089 Swivel Clamp

4205J.09 Graduated Swivel Clamp

4205J.101 CD Unit Length 40mm

4205J.1011 CD Unit Length 60mm

4205J.102 CD Unit Length 80mm

4205J.103 CD Unit Length 100mm

4205J.1031 Sandwich Plate

4205J.1032 Bolt For Sandwitch Plate

4205J.16 Lengthing Fixator Small

4205J.161 Lengthing Fixator Medium

4205J.162 Lengthing Fixator Large

4205J.168 Dyna Clamp

4205J.169 Dynamic Fixator With Ball & Socket Joint Small

4205J.17 Dynamic Fixator With Ball & Socket Joint Medium

4205J.171 Dynamic Fixator With Ball & Socket Joint Large

4205J.173S Dynamic Fixator For Elbow Small

4205J.173B Dynamic Fixator For Elbow Big

4205J.1731 Dynamic Fixator For Pelvis

4205J.1732 Penning Fixator (Wrist and Forearm)

4205J.1733 T Type Pelvic External Fixator

4205J.1734 Ankle Clamp

4205J.1735 Dynamic Ankle Fixator

4205J.1736 Multiplaner Clamp

4205J.1737 Pertrochanteric Clamp

4205J.1738 Dummy Clamp

4205J.1739 Qualis Fixator (Wrist)

4205J.174 Mono Rail Adult

4205J.1741 Finger Fixator Straight

4205J.1742 Finger Fixator 'T' Type

4205J.1743 Finger Fixator Hinge Horizontal

4205J.1744 Finger Fixator Hinge Vertical

4205J.174 Sandwich Clamp

4205J.175 Template For End & Central Clamp

4205J.176 Template For Swivel Clamp

4205J.201 Allen Key 5.0mm / 6.0mm Tip

4205J.325 Drill Bit Q.C. End 3.2mm Dia 200mm Length

4205J.205 Drill Bit Q.C. End 4.8mm Dia 200mm Length

4205J.1731 Hto Clamp (With Pins)

4205J.17311 Shanz Pin Tappered

4205J.065 Ball & Scoket - Standard

4205J.07 Ball & Scoket with T clamp

4205J.168 Dyna Ring

4205J.183 Schanz Pin Introducer

4205J.184 Troacar

4205J.185 Drill Guide 6 x 5 x 80mm

4205J.186 Screw Guide 8 x 6 x 100mm


Basic Set For Pediatric - JMS DESIGN

4205J.21 Pediatric End Clamp

4205J.215 Pediatric Central Clamp

4205J.22 Pediatric Swivel Clamp

4205J.225 Pediatric Rail 150mm

4205J.23 Pediatric Rail 200mm

4205J.235 Pediatric Rail 250mm

4205J.24 Pediatric Rail 300mm

4205J.255 Pediatric Ball & Socket Clamp

4205J.26 Pediatric Sandwich Clamp

4205J.265 Pediatric Template For End & Central Clamp

4205J.27 Pediatric C D Unit 40mm

4205J.271 Pediatric C D Unit 60mm

4205J.275 Pediatric C D Unit 80mm

4205J.505 Mini Rail With Scale For 2.0mm & 2.5mm Schanz Pin 35mm Length

4205J.51 Mini Rail With Scale For 2.0mm & 2.5mm Schanz Pin 55mm Length

4205J.515 Mini Rail With Scale For 2.0mm & 2.5mm Schanz Pin 75mm Length

4205J.52 Mini Rail With Scale For 2.0mm & 2.5mm Schanz Pin 100mm Length

4205J.525 Mini Hand Rail

4205J.5254 Hto Clamp (With Cd Unit)

4205J.5255 Dummy Clamp

4205J.5256 Mono Rail 8''

4205J.5257 Mono Rail 6''

4205J.5258 Mono Rail 4''

4205J.5259 Allen Key 3.4 / 5mm

4205J.526 Hinge Small


Rail Fixator Set Adult - JMS Design

4205JAI.001 250mm

4205JAI.002 300mm

4205JAI.003 350mm

4205JAI.004 400mm


4205JAI.005 Penning Fixator Set


Rail Fixator Set Pediatric - JMS Design

4205JPI.001 150mm

4205JPI.002 200mm

4205JPI.003 250mm


Tapered Threaded Pins Cortical Shaft 6.0mm Tapered 6.0 To 5.0mm

4205.301000 130mm X 30mm Thread

4205.302000 130mm X 40mm Thread

4205.303000 130mm X 50mm Thread

4205.310000 150mm X 30mm Thread

4205.311000 150mm X 40mm Thread

4205.312000 150mm X 50mm Thread

4205.320000 170mm X 40mm Thread

4205.321000 170mm X 50mm Thread

4205.322000 170mm X 60mm Thread

4205.330000 200mm X 40mm Thread

4205.331000 200mm X 50mm Thread

4205.332000 200mm X 60mm Thread


Tapered Threaded Pins Cortical Shaft 4.5mm Tapered 4.5 To 3.5mm

4205.410000 100mm X 20mm Thread

4205.415000 100mm X 30mm Thread

4205.420000 120mm X 30mm Thread

4205.425000 120mm X 40mm Thread


The Rail & Dynamic External Fixation System


Basic Set For Adult

4205.203000 Rail 400mm

4205.204000 Central Clamp

4205.205000 End Clamp

4205.206000 C D Unit 80mm

4205.207000 C D Unit 100mm

4205.208000 Allen Key 6mm

4205.209000 Tappered Pins


Sets For Rail Fixation System


Femur Fixation System

· Lengthening

· Correction Of Deformity With Lengthening

· Bone loss

4205.030000 Rail Length 300mm

4205.040000 Rail Length 400mm

4205.050000 Central Clamp

4205.055000 End Clamp

4205.065000 Ball Joint Coupling Clamp

4205.070000 TBall Joint Coupling Clamp

4205.090000 Graduated Swivel Clamp

4205.101000 CD Unit Length 40mm Or 60mm Or 100mm

4205.173110 Shanz Pin Special Desgin 5.5mm Tapered Thread

4205.201000 Allen Key 6.0mm Tip


Tibia Fixation System.

· Lengthening

· Correction Of Deformity With Lengthening

· Bone loss

4205.030000 Rail Length 300mm

4205.040000 Rail Length 400mm

4205.050000 Central Clamp

4205.055000 End Clamp

4205.065000 Ball Joint Coupling Clamp

4205.090000 Graduated Swivel Clamp

4205.101000 CD Unit Length 40mm Or 60mm Or 100mm

4205.173110 Shanz Pin Special Desgin 5.5mm Tapered Thread

4205.201000 Allen Key 6.0mm Tip


Humerus Fixation System.

· Lengthening

· Correction Of Deformity With Lengthening

· Bone loss

4205.030000 Rail Length 240mm Or 300mm

4205.050000 Central Clamp

4205.055000 End Clamp

4205.102000 CD Unit Length 40mm Or 80mm

4205.173110 Shanz Pin Special Desgin 4.5mm Tapered Thread

4205.201000 Allen Key 6.0mm Tip


Dynamic Axel Fixator System.

· Lengthening

· Correction Of Deformity With Lengthening

· Bone LoSS


For Femur

4205.171000 Dynamic Fixator With Ball & Socket Joint Large

4205.173110 Shanz Pin Special Desgin 5.5mm Tapered Thread

4205.201000 Allen Key 6.0mm Tip


For Femur

4205.162000 Lengthing Fixator Large

4205.173110 Shanz Pin Special Desgin 5.5mm Tapered Thread

4205.201000 Allen Key 6.0mm Tip


For Tibia

4205.170000 Dynamic Fixator With Ball & Socket Joint Medium

4205.173110 Shanz Pin Special Desgin 5.5mm Tapered Thread

4205.201000 Allen Key 6.0mm Tip


For Tibia

4205.161000 Lengthing Fixator Medium

4205.173110 Shanz Pin Special Desgin 5.5mm Tapered Thread

4205.201000 Allen Key 6.0mm Tip


For Humerus

4205.170000 Dynamic Fixator With Ball & Socket Joint Medium

4205.173110 Shanz Pin Special Desgin 4.5mm Tapered Thread

4205.201000 Allen Key 6.0mm Tip


For Humerus

4205.161000 Lengthing Fixator Medium

4205.173110 Shanz Pin Special Desgin 4.5mm Tapered Thread

4205.201000 Allen Key 6.0mm Tip


High Tibial Osteotomy System.

· Lengthing

· Correction Of Deformity With Lengthening

4205.173100 Hto Clamp

4205.173110 Shanz Pin Special Desgin 5.5mm Tapered Thread

4205.201000 Allen Key 6.0mm Tip


Elbow Fixator System.

4205.173000 Dynamic Fixator For Elbow

4205.173110 Shanz Pin Special Desgin 4.5mm Tapered Thread

4205.201000 Allen Key 5.0mm Tip


Cutter Cum Plier Hot Seller (Special Desgin)

4444.008000 Cutter Cum Plier 8"

4444.006000 Cutter Cum Plier 6"


Hoffman Fixator New Generation Big

JHF.001 5 Hole Pin Clmap (For 4mm 5mm 6mm Pins)

JHF.002 10 Holes Pin Clamp (For 4mm 5mm 6mm Pins)

JHF.003 Pelvic Clamp (For 4mm 5mm 6mm Pins)

JHF.004 Rod To Rod Coupling (For 8mm Rod Or Post)

JHF.005 Pin To Rod Coupling (For 4mm 5mm Pins / 8mm Rods Or Post)

JHF.006 Inverted Pin To Rod Coupling (For 4mm 5mm Pins / 8mm Rods Or Post)

JHF.007 Tube To Rod Coupling (For 20mm Tube / 8mm Rods Or Post)

JHF.008 4 Pin Triax Clamp (For 20mm Tube / 8mm Rods Or Post)

JHF.009 CompreSSion Distraction Device 20mm

JHF.010 Tube To Tube Clamp 20mm

JHF.011 T Adaptor 20mm

JHF.012 Straight Post 8mm

JHF.013 30Deg. Angle Post 8mm

JHF.014 90Deg. Angle Post 8mm

JHF.015 Small Semi Circular Curve Rod (Aluminium) 134mm Length

JHF.016 Medium Semi Circular Curve Rod (Aluminium) 174mm Length

JHF.017 Large Semi Circular Curve Rod (Aluminium) 214mm Length

JHF.018 Dynamization Tube 20mm Blue

JHF.0181 Dynamization Tube With Two Clamp Red

JHF.019 CompreSSion / Distraction Tube 20mm

JHF.020 Stabilisation / Reduction Wrench

JHF.021 Thumbwheel

JHF.022 7mm T Wrench / 5mm 6mm Pin Inserter

JHF.023 7mm Spanner Wrench

JHF.024 Add Force Wrench

JHF.025 Self Drilling / Self Tapping Pins (4mm 5mm 6mm)

CFR.6 Carbon Rod 65mm

CFR.7 Carbon Rod 100mm

CFR.8 Carbon Rod 150mm

CFR.9 Carbon Rod 200mm

CFR.10 Carbon Rod 250mm

CFR.11 Carbon Rod 300mm

CFR.12 Carbon Rod 350mm

CFR.13 Carbon Rod 400mm

CFR.14 Carbon Rod 450mm

CFR.15 Carbon Rod 500mm

ACR.6 Aluminium Connecting Rod 65mm

ACR.7 Aluminium Connecting Rod 100mm

ACR.8 Aluminium Connecting Rod 150mm

ACR.9 Aluminium Connecting Rod 200mm

ACR.10 Aluminium Connecting Rod 250mm

ACR.11 Aluminium Connecting Rod 300mm

ACR.12 Aluminium Connecting Rod 350mm

ACR.13 Aluminium Connecting Rod 400mm

ACR.14 Aluminium Connecting Rod 450mm

ACR.15 Aluminium Connecting Rod 500mm

SSCR.6 Stainless Steel Connecting Rod 65mm

SSCR.7 Stainless Steel Connecting Rod 100mm

SSCR.8 Stainless Steel Connecting Rod 150mm

SSCR.9 Stainless Steel Connecting Rod 200mm

SSCR.10 Stainless Steel Connecting Rod 250mm

SSCR.11 Stainless Steel Connecting Rod 300mm

SSCR.12 Stainless Steel Connecting Rod 350mm

SSCR.13 Stainless Steel Connecting Rod 400mm

SSCR.14 Stainless Steel Connecting Rod 450mm

SSCR.15 Stainless Steel Connecting Rod 500mm


Hoffman Fixator New Generation Small

SHF.001 4 Hole Pin Clmap (For 3mm & 4mm Pins)

SHF.002 Peri Articular Pin Clamp For ∅3mm Pins

SHF.003 "Rod To Rod Coupling For ∅5mm Rods Or

 Posts"

SHF.004 "Pin To Rod Couplingfor ∅5mm Rods Or Posts / ∅3 4mm

 Pins"

SHF.005 "Rod To Rod Coupling For ∅8mm Rods Or

 Posts / ∅5mm Rods

 Or Posts"

SHF.006 "Tube To Rod Coupling For ∅15mm Tube /

 ∅5mm Rods Or Posts"

SHF.007 "4 Pin Triax Clamp For ∅15mm Tube /

 ∅3 ∅4mm Pins"

SHF.008 Straight Post 5mm

SHF.009 30O Angle Post 5mm

SHF.010 CompreSSion / Distraction Tube 15mm

SHF.011 Dynamization Tube (Yellow) 15mm Tube

SHF.012 Stabilisation / Reduction Wrench

SHF.013 Thumbwheel

SHF.014 Wrench

SHF.015 5mm Spanner Wrench

SHF.016 Semi Circular Curved Rod (Stainless Steel) 111mm Length

SHF.017 Semi Circular Curved Rod (Stainless Steel) 146mm Length

SHF.018 Self Drilling / Self Tapping Pins

SCFR.6 Carbon Rod 65mm

SCFR.7 Carbon Rod 100mm

SCFR.8 Carbon Rod 150mm

SCFR.9 Carbon Rod 200mm

SCFR.10 Carbon Rod 250mm

SCFR.11 Carbon Rod 300mm

S3CR.6 Stainless Steel Connecting Rod 65mm

S3CR.7 Stainless Steel Connecting Rod 100mm

S3CR.8 Stainless Steel Connecting Rod 150mm

S3CR.9 Stainless Steel Connecting Rod 200mm

S3CR.10 Stainless Steel Connecting Rod 250mm

S3CR.11 Stainless Steel Connecting Rod 300mm


Hoffman Fixator New Generation Set For Upper Limb

4444.UL01 (5mmx5mm) Rod To Rod Clamp Small

4444.UL02 (5mmx3mm) Wire To Rod Clamp Small

4444.UL03 4 Pin CroSS Rod Clamp Small

4444.UL04 T Clamp Small

4444.UL05 Straight Rod For CroSS Pin

4444.UL06 30 ° Rod For CroSS Rod Clamp

4444.UL07 Schanz Screw Self Drilling Ø 4mm / 3mm

4444.UL08 Protecting Sleeve Ø 4mm/3mm

4444.UL09 Alliminium Alloy Connecting Rod Ø 5mm X 120150180200mm( 2 Each )

4444.UL10 Carbon Connecting Rod Ø 5mm X 120150180200mm( 2 Each )

4444.UL11 Arc S.S. Rod Ø 5mm

4444.UL12 Wrench T Handle 5mm

4444.UL13 Reduction Wrench For Stability

4444.UL14 Elbow Joint Small

4444.UL15 Quick Coupling Wire Chuck Ø 3mm

4444.UL16 Screw Driver Ø 4mm

4444.UL17 Arc Drilling Stand Small

4444.UL18 Adjust Wheel

4444.UL19 Box

4444.UL20 Basic Box


Hoffman Fixator New Generation Set For Lower Limb

4444.LL01 ( 8mm X 8mm) Rod To Rod Clamp Large

4444.LL02 ( 5mm X 8mm ) Pin To Rod Clamp Large

4444.LL03 5 Pin CroSS Rod Clamp Large

4444.LL04 Straight Rod Large For CroSS Rod Clamp

4444.LL05 30° Rod Large For CroSS Rod Clamp

4444.LL06 Schanz Screw Self Drilling Ø 5mm/6mm

4444.LL07 Protecting Sleeve Ø 5mm

4444.LL08 Aluminium Alloy Connecting Rod Ø 8mm X 200250300mm(2 Nos.Each)

4444.LL09 Carbon Fiber Connecting Rod Ø 8mm X 200250300mm( 3 N0S.Each)

4444.LL10 Half Ring Rod Large/Small

4444.LL11 Reduction Wrench For Stability

4444.LL12 Wrench With Extension Bar Large

4444.LL13 Quick Coupling Wire Chuck Ø 5mm

4444.LL14 Screw Driver Ø 7mm

4444.LL15 Drilling Stand Large

4444.LL16 Adjust Wheel

4444.LL17 Wrench T Handle 7mm

4444.LL18 Box

4444.LL19 Basic Box


Hoffman I

4444.100000 Multiaxis L Clamp For 8mm Rod Fixation Big Aluminium

4444S.100 Multiaxis L Clamp For 8mm Rod Fixation Big S.S.

4444.101000 Multiaxis L Clamp For 4.5mm Rod Fixation Small Aluminium

4444S.101 Multiaxis L Clamp For 4.5mm Rod Fixation Small S.S.

Set For Upper Limb Old Generation

4444.100000 Big 'L' Clamp With 5 Pins

4444.101000 Small 'L' Clamp With 5 Pins

4444.102000 Big 'Z' Clamp With 5 Pins

4444.103000 Small 'Z' Clamp With 5 Pins

4444.104000 Tube To Tube Clamp 8 X 8mm

4444.105000 Tube To Tube Clamp 4 X 4mm

4444.106000 Plain Connecting Rod 8mm X 250mm

4444.107000 Plain Connecting Rod 8mm X 300mm

4444.108000 Plain Connecting Rod 8mm X 350mm

4444.109000 Plain Connecting Rod 8mm X 400mm

4444.110000 Plain Connecting Rod 4mm X 200mm

4444.111000 Plain Connecting Rod 4mm X 250mm

4444.112000 Plain Connecting Rod 4mm X 300mm

4444.113000 Scanz Screw 4.5mm

4444.114000 Scanz Screw 3.5mm

4444.115000 Scanz Screw 2.5mm

4444.116000 Allen Key 3mm

4444.117000 Allen Key 4mm


Sets

4444.118000 Tibia Compound Fracture Fixation Set

4444.119000 Pelvis Fixation Set

4444.120000 T Type Fixation Set


Set For Lower Limb Old Generation

4444.100000 Big 'L' Clamp With 5 Pins

4444.099000 Mono Clamp With 5 Pins

4444.102000 Big 'Z' Clamp With 5 Pins

4444.098000 Big 'I' Clamp With 5 Pins

4444.097000 Big 'I' Clamp With 3 Pins

4444.104000 Tube To Tube Clamp 8 X 8mm

4444.106000 Plain Connecting Rod 8mm X 250mm

4444.107000 Plain Connecting Rod 8mm X 300mm

4444.108000 Plain Connecting Rod 8mm X 350mm

4444.109000 Plain Connecting Rod 8mm X 400mm

4444.096000 Scanz Screw 5.5mm

4444.113000 Scanz Screw 4.5mm

4444.117000 Allen Key 4mm

JOSH2.000 Hoffman Ii (Upper Limb)

Rod Rod Clamp Small

Wire Rod Clamp Small

CroSS Clamp Small

T Clamp Small

Straight Rod Small

30° Rod Small

Schanze Pins Dia3/4mm*80/100mm Each For 4Pcs

Protecting Sleeve Dia3/4mm

Allumium Alloy Rod Dia5.0*120/150/200mm Each For 2Pcs

Carbon Fiber Conntecting Rod Dia5.0*120/150/200mm Each For 2Pcs

T Sharped Wrench Sw5.0mm

Stability Reduction Wrench Small

Elbow Joint Small

Quicking Coupling Wire Chunk Dia. 3.0mm

Screwdriver Dia3.0/4.0mm

Quicking Coupling Wire Chunk Dia4.0mm

Arc Drilling Stand Small

Adjust Wheel

Wrist Activity Straction Device

Instrument Box


JOS.005 Ortho Telescopic Frame System Set

Full Ring

Half Ring

Foot Plate

Telescopic Struts

Threaded Rods (10Cm)

2.9mm Wires

Nuts & Bolts (With Washers)

Couplers


JOSI.005 Ortho Telescopic Frame System Standard Set With Instruments For 150mm (Id)

150/ 205mm Struts Telescopic Graduated (Expandable From 150mm To 205mm)

100mm Threaded Rods

2.9mm Thick 250mm Length Wires (Thick)

1 Hole Flat Coupler (Hinge Male)

4 Hole Flat Coupler (Post Male)

4 Hole Square Coupler (Pin Clamp/ Wrenchoqube)

Slotted Bolt (Large Slot For 2.9mm Wires)

Plain (Connection) Bolt 20mm

Strut (Shoulder) Bolt

Washers

Nuts

Nylon Nut

½ Ring 150mm (Mtl. Ai. Hard Anodized)

Full Ring 150mm (Mtl. Ai. Hard Anodized)

Foot Plate Solid 150mm (Mtl. Ai. Hard Anodized)

Spanners(Open And Ring End)

Flat Screwdriver Small 10mm Tip (Levering Strut Locks And Wires) (Small Straight Osteotome With Handle?)

Small Pliers Flat Nose ~150mm Length (Gripping Wires And Struts)

Ratchet Spanner For 10mm Nut

PRODUCT INFORMATION

Tubular external fixators are a specific type of orthopedic external fixation system used to stabilize and immobilize fractured or damaged bones. They are called "tubular" because they consist of tubular components, typically made of metal, that are connected to rings or clamps, pins or wires, and struts. Tubular external fixators are versatile and highly adjustable, allowing orthopedic surgeons to customize them for each patient's specific needs. Here are some key features and components of tubular external fixators: Rings or Clamps: Tubular fixators use rings or clamps, much like other external fixators, to anchor the system to the bone on both sides of the fracture or injury. These rings or clamps are attached to the tubular components. Tubular Components: The main feature of tubular external fixators is the use of tubular rods or struts as the connecting elements between the rings or clamps. These tubular components can be adjusted in length and orientation, making them highly versatile for various surgical applications. Connecting Rods: Tubular fixators use tubular connecting rods or struts to provide stability and alignment between the rings or clamps. These connecting rods can be easily adjusted and locked in place. Pins or Wires: To secure the rings or clamps to the bone, pins or wires are used. These anchoring devices are inserted through the skin and into the bone, providing a stable connection point for the fixator. Adjustability: The tubular components are highly adjustable, allowing for precise alignment and positioning of the bone. This adjustability is crucial for accommodating changes in the healing process and ensuring optimal bone alignment. Biocompatibility: Materials used in tubular external fixators are typically biocompatible to minimize the risk of allergic reactions or tissue rejection. Tubular external fixators are used in various orthopedic situations, including complex fractures, limb length discrepancies, limb deformities, bone infections, and non-unions or malunions. The specific configuration and design of the fixator may vary depending on the patient's condition and the surgeon's preference. One of the advantages of tubular external fixators is their versatility and ease of adjustment, making them suitable for a wide range of orthopedic procedures. They can be fine-tuned during surgery to ensure the desired bone alignment and stability. Once the bone has healed sufficiently, the fixator is typically removed. The choice of external fixator and its placement is determined by the orthopedic surgeon based on the patient's specific needs and the nature of the injury or condition.

Orthopedic external fixator clamps are devices used in orthopedic surgery to stabilize fractured or injured bones. External fixators are often used when traditional casting or internal fixation methods are not suitable for a particular injury or when there's a need for more precise control over bone alignment and stability. These devices consist of various components, including clamps, which play a crucial role in holding the bone fragments in place. Here's some information about orthopedic external fixator clamps: Types of Clamps: There are different types of clamps used in external fixators, and they serve specific purposes. Some common types include: Pin Clamps: These clamps attach to the pins or wires that are inserted into the bone. They secure the pins to the fixator frame. Rod-to-Rod Clamps: These clamps are used to connect two or more rods of the fixator frame, allowing for adjustments in the fixation construct. Rod-to-Pin Clamps: These clamps connect rods and pins, providing flexibility in construct design. Material: External fixator clamps are typically made of medical-grade stainless steel or other biocompatible materials. They must be durable, corrosion-resistant, and capable of withstanding the forces applied during the healing process. Adjustability: Clamps in external fixators are designed to be adjustable. This allows the surgeon to fine-tune the alignment of the bone fragments during surgery and make necessary adjustments as the healing process progresses. Security: The primary function of these clamps is to securely hold the components of the external fixator in place. This stability is essential for ensuring proper bone healing. Ease of Use: The clamps need to be easy for surgeons to attach and detach, especially during surgery when time is critical. Many of them have quick-release mechanisms for this purpose. Sterilization: Like other surgical instruments, external fixator clamps must be sterilized to prevent infections. This typically involves autoclaving them before use in surgery. Compatibility: External fixator clamps are designed to be compatible with a variety of external fixator systems, so surgeons can choose the right components for their specific surgical needs. Radiolucency: Some clamps are designed to be radiolucent, meaning they don't obstruct X-ray or other imaging procedures. This feature allows for monitoring the healing process without having to remove or reposition the fixator. Orthopedic external fixator clamps are essential tools in the field of orthopedic surgery. They play a critical role in the treatment of complex fractures, deformities, and other orthopedic conditions by providing stable support and alignment for the bones during the healing process. The choice of clamps and fixator components depends on the specific surgical case and the preferences of the surgeon.

An external fixator is a medical device used in orthopedic surgery to stabilize and immobilize fractured bones, including those in the forearm and metacarpals (the bones in the hand). External fixators are typically used when traditional casting or internal fixation methods are not suitable for a particular injury or when there's a need for precise alignment and stability of the fractured bones. Here's how an external fixator works in the context of forearm and metacarpal fractures: Placement: The orthopedic surgeon places pins or wires into the bones on either side of the fracture, typically above and below it, to anchor the external fixator. Frame Assembly: Once the pins or wires are in place, a frame is assembled around the injured area. This frame consists of rods and clamps, which are adjusted to maintain the correct alignment of the fractured bones. Stabilization: The fixator is secured in place, providing stability to the fractured bones, preventing further displacement, and allowing for optimal alignment to promote proper healing. Adjustments: The orthopedic surgeon may make periodic adjustments to the external fixator as the healing process progresses to ensure that the bones continue to heal in the desired position. External fixators are useful in cases of complex fractures, open fractures, severe soft tissue injuries, or when there is a need for early joint mobility during the healing process. They provide a way to maintain the fracture reduction without casting the limb, which can be beneficial in certain situations. It's important to note that external fixators are typically not a permanent solution. Once the bones have healed sufficiently, the external fixator is removed, and the patient may undergo rehabilitation to regain strength and mobility in the affected limb.

A Colles Fixator is an orthopedic device used in the treatment of distal radius fractures, which are fractures of the radius bone in the forearm near the wrist, specifically fractures in the Colles' region. The Colles' region refers to the distal part of the radius bone that is closer to the wrist joint. A Colles Fixator is designed to stabilize the fractured bone and maintain proper alignment during the healing process. It typically consists of pins or wires inserted into the bone and an external frame or support structure that holds the fractured bone segments in place. This fixator is used to provide stability and support to the fractured radius, allowing for proper healing and alignment of the bone. The specific design and components of a Colles Fixator may vary, but the primary goal is to assist in the treatment of distal radius fractures, which are common injuries, particularly in older individuals who may experience osteoporosis-related fractures. Orthopedic surgeons use these fixators as one of the treatment options for such fractures, and they may be applied surgically to realign and stabilize the broken bone.

The Aesculap clamp is a surgical instrument commonly used in orthopedic surgery. It is a type of surgical clamp specifically designed for use in orthopedic procedures. These clamps are used to grasp and hold bone fragments or other structures during surgery. They come in various shapes and sizes to accommodate different types of orthopedic procedures, such as fracture reduction, fixation of bones, or joint reconstruction. Aesculap is a well-known manufacturer of medical and surgical instruments, including orthopedic instruments like clamps, bone plates, screws, and other tools. These instruments are made from high-quality materials and are designed to meet the specific needs of orthopedic surgeons during various surgical procedures. The choice of a specific Aesculap clamp in orthopedic surgery will depend on the surgeon's preferences and the requirements of the particular procedure. It's important for surgeons to use the appropriate instruments to ensure the safety and success of the surgery.

In orthopedics, a "Tube-to-Tube Clamp" typically refers to a type of orthopedic implant or device used in the assembly of external fixation systems. External fixation is a technique used to stabilize fractured bones or correct deformities by using metal pins, wires, or screws inserted into the bone and then connecting them with tubes or rods to create a stable frame around the affected area. These external fixation systems are often used in complex fractures, limb lengthening procedures, and in cases where traditional cast immobilization may not be sufficient. The "Tube-to-Tube Clamp" is an essential component of such external fixation systems. It allows the secure attachment of the various rods and tubes, enabling the orthopedic surgeon to customize the frame's configuration and adjust it as needed for the patient's specific condition. The exact design and usage of these clamps can vary depending on the specific external fixation system and the surgeon's preferences. These clamps are typically made of durable materials such as stainless steel or titanium to ensure stability and patient comfort. Please note that the specific terminology and devices used in orthopedics may change over time, so it's always best to consult with a qualified orthopedic surgeon or medical professional for the most up-to-date information and guidance on orthopedic devices and procedures.

Tubular rods are often used in orthopedic surgery as a component of fixation systems, especially in procedures involving the spine. They are typically made of materials like titanium or stainless steel and can be straight or contoured to match the anatomical requirements of the patient. These rods are part of a larger system used to stabilize and support the spine or other bones in orthopedic surgery. Here are a few key points regarding tubular rods in orthopedics: Spinal Fusion: In spinal surgery, tubular rods are commonly used in conjunction with screws, hooks, or other fixation devices to create a stable construct. This helps in spinal fusion procedures, where two or more vertebrae are fused together to treat conditions such as scoliosis, degenerative disc disease, or spinal fractures. Customization: Tubular rods can be customized in terms of length and contour to match the specific needs of the patient. Surgeons may bend or shape the rods during the surgery to ensure proper alignment and fixation. Material: These rods are typically made from biocompatible materials like titanium or stainless steel, which are known for their strength and resistance to corrosion. Advancements: There have been ongoing advancements in orthopedic technology, leading to the development of more flexible and dynamic rod systems for spinal surgeries, allowing for greater range of motion after surgery. Surgical Techniques: The use of tubular rods in orthopedic surgery is just one aspect of a larger surgical procedure. The surgeon will decide on the specific approach, instrumentation, and techniques based on the patient's condition and the surgical goals.

A tubular external fixator set is a medical device used in orthopedic surgery to stabilize fractures or to support and align bone segments. External fixation is a method of immobilizing and stabilizing broken bones using devices that are outside the body. The tubular external fixator set typically consists of a series of metal tubes, pins, clamps, and connecting rods. Here's a brief overview of the components and how they are used: Tubular Frames: These are the main structural components of the external fixator. They are made of strong, lightweight materials such as aluminum or stainless steel. Pins: Pins are inserted through the skin and into the bone to hold the fixator in place. They are attached to the tubular frame using clamps. Clamps: Clamps secure the pins to the tubular frame. They come in various designs to allow for flexibility in pin placement and fixation angles. Connecting Rods: Rods connect different parts of the tubular frame, providing stability and support. They can be adjusted in length to achieve the desired configuration. Locking Mechanisms: Some external fixators have locking mechanisms that allow the surgeon to fix the length of the connecting rods, providing additional stability. Half-Pins or Full-Pins: These are types of pins used to secure the fixator to the bone. Half-pins are inserted through the skin, while full-pins are inserted directly into the bone. The external fixator is assembled around the fractured area, and the pins are inserted into the bone on either side of the fracture. The connecting rods are then adjusted to bring the bone fragments into the desired alignment and maintain stability during the healing process. Tubular external fixators are versatile and can be used in a variety of orthopedic procedures, including the treatment of complex fractures, limb lengthening, and correction of deformities. They are especially useful when traditional methods of internal fixation (like plates and screws) are not suitable for a particular case.

he AO (Arbeitsgemeinschaft für Osteosynthesefragen) classification is a widely used system in orthopedic surgery for the classification of fractures and the selection of appropriate implants for fracture fixation. The AO classification includes three main categories: AO/OTA, AO/ASIF, and AO/OTA/Arbeitsgemeinschaft für Osteosynthesefragen (AO) Foundation/Arbeitsgemeinschaft für Studium und Ausbildung in der Traumatologie (ASIF).  "External Fixator Set AO TYPE" in the context of orthopedic surgery, it likely means a set of external fixators designed based on the principles of the AO classification for fracture management. External fixators are devices used in orthopedic surgery to stabilize fractures and promote bone healing. They consist of pins or wires inserted into the bone on either side of the fracture, connected by an external frame. The AO classification helps in selecting the appropriate type of fixator based on the nature and location of the fracture. It's important to note that the specific components and designs of external fixator sets may vary between manufacturers. If you are looking for a particular set, you should consult the manufacturer's catalog or contact the supplier for detailed information on the contents and specifications of the External Fixator Set AO TYPE you are interested in.

The Ilizarov external fixator is a medical device used in orthopedic surgery to treat various conditions, including fractures, limb length discrepancies, and deformities. It is named after the Russian orthopedic surgeon Dr. Gavriil Abramovich Ilizarov, who pioneered its development in the 1950s. The Ilizarov external fixator consists of metal rings, wires, and pins that are surgically attached to the affected bone or bones. These components are connected to each other by threaded rods, creating a stable frame around the limb. The device is external, meaning it is positioned outside the body. Here are some key features and applications of the Ilizarov external fixator:Modularity: The fixator is modular, allowing surgeons to customize the frame according to the patient's specific anatomy and the nature of the injury or deformity. Circular Fixation: The circular arrangement of rings provides stability in multiple planes, allowing for more precise control over the alignment and length of the bones. Distraction Osteogenesis: One of the significant contributions of Ilizarov's technique is the concept of distraction osteogenesis. By gradually pulling apart bone segments, new bone tissue fills in the gap, effectively lengthening the bone. This is particularly useful in treating limb length inequalities. Reduced Soft Tissue Disruption: Unlike traditional internal fixation methods, the Ilizarov external fixator minimizes disruption to the surrounding soft tissues, which can lead to faster healing and reduced risk of infection. Versatility: The Ilizarov fixator can be used to treat a wide range of orthopedic conditions, including complex fractures, non-unions (failure of a bone to heal), malunions (improperly healed fractures), and various congenital or acquired deformities. Postoperative Adjustability: The fixator allows for postoperative adjustments, enabling the surgeon to fine-tune the alignment or make corrections as needed during the course of treatment. Despite its effectiveness, the Ilizarov external fixator has some limitations, such as patient discomfort and the need for careful postoperative care. Advances in technology and surgical techniques continue to refine external fixation systems, but the Ilizarov method remains a valuable tool in the orthopedic surgeon's arsenal for treating challenging cases.

Ilizarov fixators use circular metal rings as a key component of the external fixation system. These rings are typically made of stainless steel or other biocompatible materials. The Ilizarov method involves securing these rings to the bone with wires or pins, and the rings are then connected by adjustable struts. Here's a basic overview of how Ilizarov fixators work: Ring Application: Surgeons attach the metal rings to the bone using wires or pins that penetrate the skin and bone. The rings are placed above and below the area that needs correction or stabilization. Wire and Pin Placement: Wires or pins are passed through the skin and bone, connecting the rings to the bone. These wires or pins provide stability and allow for the transmission of forces necessary for bone healing or correction. Adjustable Struts: The rings are connected by adjustable struts or rods. These struts can be lengthened or shortened over time to gradually correct deformities or lengthen bones. The adjustments are typically made in small increments to avoid excessive stress on the surrounding tissues. External Frame: The entire system forms an external frame around the limb, allowing for controlled and gradual correction. The external fixation provides stability and support for the healing or correction process. Ilizarov fixators are commonly used in various orthopedic conditions, including limb lengthening, correction of deformities, and treatment of complex fractures. The method is known for its versatility and effectiveness in addressing challenging orthopedic issues.

The Ilizarov wire is a component of the Ilizarov apparatus, a device used in orthopedic surgery for limb lengthening, deformity correction, and fracture treatment. The Ilizarov method was developed by Russian orthopedic surgeon Dr. Gavriil Ilizarov. The Ilizarov apparatus typically includes external rings, wires, and pins. Here's a brief overview of the Ilizarov wire and its role in the treatment process: Material and Construction: Ilizarov wires are usually made of stainless steel or other biocompatible materials. They come in various diameters and lengths, depending on the specific needs of the patient and the surgical procedure. Application: Surgeons use Ilizarov wires to secure the external rings of the Ilizarov apparatus to the bone. The wires are passed through the soft tissues and bone, providing a stable external fixation system. Role in Limb Lengthening: One of the primary applications of the Ilizarov method is limb lengthening. By adjusting the tension in the wires, surgeons can gradually pull apart bone segments, allowing new bone to form in the gap. This process is known as distraction osteogenesis. Deformity Correction: The Ilizarov apparatus is also used for correcting various orthopedic deformities, such as angular deformities or rotational abnormalities. The adjustable nature of the apparatus allows for precise control over the correction process. Fracture Treatment: In cases of complex fractures or non-unions (failure of a fracture to heal), the Ilizarov method may be employed to stabilize the fracture site and promote bone healing.

Cerclage wiring is a technique used in orthopedic surgery, particularly in the treatment of certain fractures. The term "cerclage" is derived from the French word meaning "encircle" or "hoop." In orthopedics, cerclage wires are used to encircle and secure fractured bone segments, providing stability and support during the healing process. Here's a brief overview of how cerclage wiring is commonly used: Fracture Stabilization: Cerclage wires are often used in the management of fractures, especially those in long bones like the femur or tibia. Encircling the Bone: The surgeon places a wire or wires around the fractured bone, creating a loop or circle. This can help bring fractured segments together and provide stability. Tensioning: The wires are tightened to ensure a snug fit and maintain alignment of the fractured fragments. Fixation: Cerclage wires may be used in conjunction with other forms of fixation, such as plates and screws, to provide comprehensive stability.

In the context of orthopedics, nuts, bolts, and washers typically refer to the hardware components used in orthopedic implants. These implants are often used in the surgical treatment of fractures, joint replacements, and other orthopedic conditions. Here's a brief overview of each component: Nuts: In orthopedics, nuts are threaded fasteners with a central hole designed to screw onto a threaded bolt. They are used to secure various orthopedic implants in place. The nut's design and material may vary depending on the specific application and the type of implant being used. Bolts: Orthopedic bolts are threaded rods or screws that are inserted into bone to provide stability and support. They are often used in conjunction with plates, screws, or other fixation devices. Bolts come in different lengths, diameters, and materials, and the selection depends on factors such as the type and location of the fracture or orthopedic condition being treated. Washers: Washers are flat, typically circular, metal discs with a central hole. In orthopedics, washers are used in conjunction with nuts and bolts to distribute pressure more evenly over the bone surface when the implant is tightened. This helps to prevent damage to the bone and ensures a more stable fixation. Orthopedic hardware is made from materials such as stainless steel, titanium, or cobalt-chromium alloys. These materials are chosen for their biocompatibility and strength. The specific choice of hardware depends on factors such as the patient's anatomy, the type of surgery, and the surgeon's preferences. It's important to note that orthopedic hardware is used to stabilize fractures or support joint replacement components, and the choice of hardware is determined by the specific needs of the patient and the surgical procedure.

The Ilizarov method, named after the Russian orthopedic surgeon Gavriil Abramovich Ilizarov, is a technique used in orthopedic surgery for limb lengthening, deformity correction, and fracture healing. The method involves the use of an external fixator device, and it has been adapted for use in pediatric patients as well. Pediatric Ilizarov external fixators are used in children for a variety of conditions, including congenital deformities, limb length discrepancies, and complex fractures. The external fixator consists of metal rings, wires, and pins that are attached to the bones, allowing for precise control over the alignment and lengthening of the affected limb. Here are some key points about pediatric Ilizarov external fixators: Congenital Deformities: Ilizarov external fixators can be used to correct congenital deformities in children, such as clubfoot or limb length inequalities. Limb Lengthening: One of the primary applications of the Ilizarov method in pediatric patients is limb lengthening. This is often done to address conditions where one limb is shorter than the other. Fracture Management: Ilizarov external fixators are used in the treatment of complex fractures in children. The external fixation allows for stability and control of the fracture site during the healing process. Gradual Correction: The Ilizarov method relies on the principle of gradual correction. Small adjustments are made over time to achieve the desired alignment or lengthening. This gradual process minimizes complications and allows for bone and soft tissue adaptation. Multidirectional Correction: The external fixator allows for multidirectional correction, meaning that deformities can be corrected in various planes, including rotation, angulation, and translation. Outpatient Management: In many cases, pediatric patients treated with Ilizarov external fixators can be managed on an outpatient basis. This reduces the need for prolonged hospital stays. Physical Therapy: Physical therapy is often an integral part of the treatment plan. It helps optimize functional outcomes and promotes the development of motor skills during the limb lengthening or deformity correction process. Monitoring and Follow-up: Close monitoring and follow-up with the orthopedic team are crucial throughout the treatment period. Regular radiographic assessments are performed to evaluate progress and make necessary adjustments.

The correct term is "CTEV" (Congenital Talipes Equinovarus), which refers to a congenital condition more commonly known as clubfoot. Jess Fixator is a type of external fixator system used in the treatment of clubfoot. The Jess Fixator system is designed to correct deformities associated with clubfoot. It typically consists of an external frame with adjustable components that are attached to the affected limb. The fixator allows gradual adjustment of the foot position to correct the abnormal alignment of the bones and soft tissues in clubfoot. The use of a Jess Fixator is part of a treatment approach that may also involve casting, stretching exercises, and, in some cases, surgical intervention to achieve proper alignment of the foot.

Tapered threaded pins for the cortical shaft are commonly used in orthopedic surgery, particularly in external fixation systems. These pins are designed for insertion into the cortical bone, which is the dense outer layer of bone. The tapering and threading of the pins provide stability and help secure the pin within the bone. Here are some key features and considerations: Tapered Design: The tapered shape of the pin allows for easier insertion into the bone. It helps to create a more secure fit by gradually increasing in diameter from the tip to the base. Threaded Surface: The threaded portion of the pin enhances fixation by engaging with the bone tissue, providing additional stability. The threads on the pin help prevent migration and loosening. Cortical Shaft Targeting: These pins are specifically designed for use in the cortical bone, which is the hard, dense outer layer of bone. This type of bone is commonly found in the shafts of long bones. Material: The pins are typically made from biocompatible materials such as stainless steel or titanium, which are well-tolerated by the body. Surgical Technique: Insertion of these pins involves drilling a hole into the cortical bone and carefully placing the tapered threaded pin. The surgical technique may vary depending on the specific external fixation system or orthopedic procedure being performed. Orthopedic surgeons use these pins as part of external fixation systems to stabilize fractures, correct deformities, or provide support during bone healing. The choice of pin design may depend on factors such as the type and location of the fracture, patient anatomy, and the surgeon's preference.

A High Tibial Osteotomy (HTO) System is a medical device used in orthopedic surgery to treat certain knee conditions, particularly those involving the knee joint's alignment. This procedure involves cutting and repositioning the upper part of the tibia (shinbone) to relieve pressure on a damaged or arthritic area of the knee. The primary goal of a high tibial osteotomy is to shift the weight-bearing axis away from the damaged or affected part of the knee joint, redistributing the load to healthier portions. This can help alleviate pain and slow down the progression of arthritis in the knee. HTO is often considered for patients with medial compartment osteoarthritis or other conditions where realigning the knee may be beneficial.

An elbow fixator system is a medical device designed to stabilize and immobilize the elbow joint during the healing process after a fracture, surgery, or other traumatic injuries. The elbow is a complex joint, and its proper functioning is crucial for daily activities. In cases where there is a need for external support and stabilization, a fixator system may be employed. The fixator system typically consists of various components that work together to provide stability and support to the elbow. These components may include: Frame or Brace: The main structure of the fixator, often made of lightweight materials like aluminum or titanium, that surrounds the elbow joint. Hinges and Joints: Articulating parts that allow controlled movement or fixation of the elbow. These can be adjusted based on the patient's condition and the stage of the healing process. Straps or Fasteners: Secure the fixator in place, ensuring proper alignment and preventing movement that could impede the healing process. Locking Mechanisms: Some fixators have the option to lock the joint in a specific position, restricting movement during critical phases of recovery. Adjustability: Many fixators are adjustable to accommodate changes in swelling, tissue size, or the need for different degrees of joint movement at different stages of rehabilitation.